Search Thermo Fisher Scientific
Magnetic Beads for Immunoprecipitation |
Immunoprecipitation (IP) is a cellular and molecular biology method used in laboratories to isolate or purify a specific antigen (or protein of interest) via a solid phase (agarose or Sepharose™ resin or magnetic particles). The IP method was first performed on small aliquots of agarose resin in microcentrifuge tubes. Use of magnetic beads is one method of isolating your protein of interest via IP. Dynabeads, DynaGreen, and Pierce magnetic beads for IP offer exceptional balance of capacity/yield, reproducibility, purity, and cost for smaller-scale isolation of specific proteins (e.g., IP) and protein complexes (co-IP).
Selection guide for Dynabeads products
Dynabeads products are available for a multitude of molecular and cellular applications. Don’t know where to start? Use our easy selection guide that considers sample type, target molecule, and downstream application to provide tailored recommendations for Dynabeads products.
On this page:
What is immunoprecipitation?
Immunoprecipitation (IP) is a cellular and molecular biology method used in laboratories to isolate or purify a specific antigen (or protein of interest) via a solid phase (agarose or Sepharose™ resin or magnetic particles). The IP method was first performed on small aliquots of agarose resin in microcentrifuge tubes. The IP method has evolved to use superparamagnetic particles to specifically target proteins of interest.
How does immunoprecipitation work?
The Dynabeads magnetic beads IP procedure is simple, fast, requires no preclearing step, and results in high-target protein purity, yield, and consistent results. Both DynaGreen magnetic beads and Pierce magnetic beads can perform the same steps with slightly longer protocol times to complete. DynaGreen protocol finishes in <80min. Pierce protocol finishes in <120min.
Step 1: Binding of the antibody to the beads
Dynabeads, DynaGreen, and Pierce magnetic beads come pre-coated with protein A, protein G, anti-mouse IgG, or anti-rabbit IgG antibodies. Their rapid kinetics allow them to bind to the added antibody in about ten minutes (Figure 1). Biotinylated antibodies can also be used in combination with streptavidin-coupled Dynabeads and Pierce magnetic beads. After antibody incubation a wash step is performed to remove unbound antibodies.
Step 2: Add sample to the beads
The protein-containing sample is added to the beads-antibody mix and incubated for ten minutes to allow target protein binding. If the protein is of low abundance or low affinity, the incubation time can be increased to one hour or overnight. For most cases, a ten-minute incubation is sufficient.
Step 3: Wash the protein-bound beads
To help ensure high purity of the bound target protein, the beads should be washed 2 to 4 times with buffer on the magnet to remove all unbound proteins. This step in the isolation process helps ensure a high signal-to-noise ratio.
Step 4: Elute the protein
The protein can be eluted off the beads by using either a mild elution procedure or a denaturing elution procedure (Figure 2).
Click image to enlarge
Figure 1. Immunoprecipitation protocol with magnetic beads.
Figure 2. Types of elution buffers for immunoprecipitation with magnetic beads. Depending on your target protein and how they bind to the magnetic beads, there are three main types of elution buffers to unbind the target protein. Denaturing elution buffers are used for SDS-PAGE. Mild elution buffers are used for protein characterization, immunization, enzyme studies, amino acid sequence determination, and crystallization. Protein-protein interactions, enzyme studies, bioassays, and immunoassays may be performed without eluting your target protein from the magnetic beads.
Why are magnetic beads used in immunoprecipitation?
Magnetic beads for IP have become more common, especially compared to the traditional method of using agarose slurries or resin for protein isolation. This is because magnetic immunoprecipitation beads provide several advantages over the traditional method, such as:
- Low background—Little to no non-specific binding and no preclearing required for high-purity protein yields
- Highly reproducible—Uniform composition of the magnetic beads ensures the most consistent results
- Highly sensitive—Most-cited method for sensitive applications, such as ChIP and IP for low- abundance proteins
- Fast and easy—<40 min protocol with no centrifugation or preclearing steps
- Antibody savings—All binding occurs on the smooth outer surface of the beads, which conserves precious antibodies compared to porous agarose beads; using beads for IP is a cost-efficient solution per sample
- Automation compatible—Immunoprecipitation beads protocol can be automated on the Thermo Fisher Scientific KingFisher platform
View common IP myths on agarose resins vs magnetic beads
Learn about co-immunoprecipitation
Immunoprecipitation beads selection guide
- Antibody-binding magnetic beads—Most common method
- Fusion tag-binding magnetic beads—If your protein is a recombinant protein
- Biotin-binding magnetic beads—If your protein is biotinylated
- Surface-activated magnetic beads—If your ligand or target sample is tricky
Antibody-binding magnetic beads for IP
| Protein A, G, A/G | Secondary antibodies (anti-mouse, anti-rabbit) | |
|---|---|---|
| Recommended products | Beads only:Kits: | Beads only: |
| Binding properties | Non-covalent antibody binding | |
| Antibody co-eluted off the beads | Yes* No (Pierce Crosslink Magnetic IP/Co-IP Kit) | Yes* |
| Type of ligand | Different ligands bind different species and antibody subclasses with different specificity† |
|
| Mass spec compatible | Yes
| Yes No (Dynabeads M-280) |
| Non-specific binding | Low | |
* Crosslinking can be performed to avoid co-elution of the antibody, but this can decrease the yield of the target antigen.
† Learn which antibody-binding proteins are best for your IP antibody.
Dynabeads magnetic beads compared to Sepharose- and agarose-based solutions
Click image to enlarge
Figure 3. Shorter protocol time and better target protein yields with Dynabeads magnetic beads. Equal amounts of sample material with respect to Ab content and cell lysate volume were used for all IP protocols according to the manufacturer’s protocol. For the Dynabeads-based method, all the antibodies on the bead surface are accessible for optimal, highly reproducible antigen binding.
Dynabeads magnetic beads compared to competitor magnetic beads
Click image to enlarge
Figure 4. Electron microscopy of Dynabeads magnetic beads compared to competitor magnetic beads. (A) Dynabeads magnetic beads have a defined surface to carry out the necessary binding with no inner surface to trap any unwanted proteins. Dynabeads products are the most uniform, monodisperse superparamagnetic beads, manufactured with highly controlled product qualities to enable a high degree of reproducibility. (B–D) Magnetic particles from alternative suppliers have variable shapes and sizes that trap impurities, resulting in lower reproducibility and increased non-specific binding.
Dynabeads magnetic beads compared to competitor magnetic beads for IP
Click image to enlarge
Figure 5. Dynabeads magnetic beads have exceptional immunoprecipitation performance with the combination of highest yield and lowest non-specific binding. (A) Silver staining of the protein membrane shows that Dynabeads magnetic beads have the most enriched binding at the antibody main band and very low non-specific binding with low signal/noise. (B) Western blot analysis of CD81 pulldown in Jurkat cells show that Dynabeads Protein G beads have the highest yield with a short ten-minute protein incubation.
Fusion tag-binding magnetic beads for IP
| Tag | c-Myc | FLAG | HA | Histidine | GST |
|---|---|---|---|---|---|
| Description |
|
|
|
|
|
Recommended products |
His and GST are not true epitope tags, because they are not usually purified or detected via specific antibodies. By contrast, HA and c-Myc tags are true epitope tags, because their only means of purification or detection is via specific antibodies. Epitope tags are seldom used for bulk purification but are most often used for IP or co-IP. Nevertheless, all four of these tag systems can be used for either purification or pull-down applications.
Biotin-binding magnetic beads for IP
Main advantages of magnetic beads for biotin-binding:
- If you have a sample rich in soluble IgGs
- If you have a recombinant antibody lacking Fc regions
- If you need a bead compatible with mass spectrometry
Surface-activated magnetic beads for IP
If your target protein or ligand needs to be covalently coupled, use surface-activated beads
Different ligands (antibodies, proteins, etc.) require different bead surface properties and immobilization chemistries. Choose surface-activated beads to control factors such as:
- Hydrophobicity: choose hydrophilic of hydrophobic beads
- Bead size: 1 µm, 2.8 µm, and 4.5 µm beads available
- Surface chemistry: epoxy, amine, or tosylactivated
Automate your sample preparation using Dynabeads magnetic beads with protocols for Kingfisher instruments
KingFisher instruments automate the isolation of DNA, RNA, proteins, exosomes, viruses, and cells. KingFisher instruments help eliminate cross contamination, produce reproducible results, and cut your hands-on time down to 40 minutes. Set up plates, press start, and walk away.
Learn more about KingFisher instruments for automated protocols
Searching for high-performing, sustainable magnetic beads? Introducing DynaGreen Magnetic Beads.
DynaGreen Magnetic Beads provide high-quality, reproducible results and are also environmentally friendly and microplastic-free. How do these beads contribute to a more sustainable science? All DynaGreen Magnetic Beads have the following features:
- Non-microplastic bead core
- Energy-efficient manufacturing
- Reduced water consumption
- Use of non-hazardous chemicals
- Recyclable packaging
- Paperless documents
Videos on immunoprecipitation
Immunoprecipitation with Dynabeads magnetic beads FAQs
Here are some frequently asked questions regarding the use of Dynabeads magnetic beads for immunoprecipitation.
A: Dynabeads Protein A and Dynabeads Protein G are 2.8-micron beads covalently coupled with Protein A and recombinant Protein G, respectively. Protein A and Protein G differ in their binding strength to immunoglobulins from different species and subclasses.
A: 1. Verify binding/specificity of your antibody to your antigen (e.g., by ELISA).
2. Check the binding of your antibodies to the beads. If the antibodies are not captured and bound to the beads, the immunoprecipitation experiment will not work.
3. If you have used the indirect method of immunoprecipitation, try the direct method. Conversely, if you have used the direct method, try the indirect method.
4. Check the amount of beads and sample volume. With reference to the capacity of different beads proposed in the package inserts, increase the amount of beads or the concentration of your antibody during coupling.
5. Increase the incubation time.
6. Try another antibody.
A: Yes, you can use the larger beads. Note: Smaller beads provide a larger surface area and therefore give higher yields of protein compared to the larger 4.5-micron beads.
Immunoprecipitation publications using Dynabeads magnetic beads
- Brinkmalm A., Öhrfelt A., Bhattacharjee P., et al. (2019) Detection of α-Synuclein in Biological Samples Using Mass Spectrometry. Methods Mol Biol 1948:209–220.
- Bafunno V., Firinu D., D’Apolito M., et al. (2018) Mutation of the angiopoietin-1 gene (ANGPT1) associates with a new type of hereditary angioedema. J Allergy Clin Immunol 141(3):1009–1017.
- Stanton BZ., Hodges C., Crabtree GR., et al. (2017) A General Non-Radioactive ATPase Assay for Chromatin Remodeling Complexes. Curr Protoc Chem Biol 9(1):1–10.
View publications on cell isolation using Dynabeads products
View publications on Dynabeads Streptavidin magnetic beads
Additional publications can be found in our Citations and References database. The database can be searched using a product catalog number or keyword. For example, searching with the term "10001D" will return a list of journal articles that cite the use of Dynabeads Protein A for Immunoprecipitation (Cat. No. 10001D) and searching with the term "dynabeads" will return a list of journal articles that cite the use of any Dynabeads product. Note that the Citations and References database on thermofisher.com contains only the small subset of scientific journal articles that cite the use of our products. Many more can be found via targeted searches of the PubMed™ database and similar databases.
Ordering information
Immunoprecipitation related content
Literature
Resources
Hero banner dark gradient overlay
© 2023 Thermo Fisher Scientific Inc. All rights reserved. All trademarks are the property of Thermo Fisher Scientific and its subsidiaries unless otherwise specified.
ACT is a trademark of My Green Lab.
Magne is a trademark of Promega Corporation.
Sepharose is a trademark of Cytiva Bioprocess R&D AB.
SureBeads is a trademark of Bio-Rad Laboratories, Inc.
Sera-Mag is a trademark of Hyclone Laboratories, LLC.
GenScript is a trademark of Nanjing GenScript Biotech Co.
PureProteome is a trademark of Millipore Corporation.
Stylesheet for Classic Wide Template adjustments
For Research Use Only. Not for use in diagnostic procedures.